Malaysian DIYer shows you how to make a pet feeder stand


Did you know that cats and dogs can get chin acne? When I discovered that my cats had it, and that one possible cause was their plastic food bowls, I knew I had to take action.

After doing some research and consulting with the vet, I learned that switching to stainless steel bowls was the best solution. So, I decided to make a DIY feeder stand for their new stainless steel bowls to make mealtime extra special.

What’s even better is that the stand matches perfectly with my home decor. It’s practical and blends beautifully with my wooden furniture and overall aesthetics.

Plus, elevating their food bowls aids digestion, making this project both stylish and functional. This simple yet creative DIY project is the perfect way to show your pets a little extra love while keeping your home looking aesthetically pleasing.

Whether you have cats or dogs, you can easily build your own custom wooden feeder stand with only one piece of wood.

PROJECT - DIY Feeder Stand

Materials

1 piece of 20cm x 60cm wood

2 stainless steel bowls (12cm diameter)

Tools

Ruler

Drill driver

Hammer

Jigsaw

Sander

Personal Protective Equipment (PPE)

Mask

Goggles

1. You’ll need one piece of wood measuring 20cm x 60cm for the project. Adjust according to your pet’s bowl size.

You’ll need one piece of wood measuring 20cm x 60cm for the project. Adjust according to your pet’s bowl size. Photos: Aida IhsaniYou’ll need one piece of wood measuring 20cm x 60cm for the project. Adjust according to your pet’s bowl size. Photos: Aida Ihsani

2. Measure two 10cm sections, each for the legs, leaving the remaining 40cm as the top. Draw lines to separate the pieces. The height of the legs should be adjusted to match the height of your pet’s neck to ensure a comfortable eating position.

Measure two 10cm sections, each for the legs, leaving the remaining 40cm as the top. Draw lines to separate the pieces. The height of the legs should be adjusted to match the height of your pet’s neck to ensure a comfortable eating position.Measure two 10cm sections, each for the legs, leaving the remaining 40cm as the top. Draw lines to separate the pieces. The height of the legs should be adjusted to match the height of your pet’s neck to ensure a comfortable eating position.

3. Using a jigsaw, carefully cut the two 10cm leg pieces and the 40cm top piece.

Using a jigsaw, carefully cut the two 10cm leg pieces and the 40cm top piece.Using a jigsaw, carefully cut the two 10cm leg pieces and the 40cm top piece.

4. For the top, measure 8mm from each short side and mark four evenly spaced intervals. Trace the bowl outlines side by side, leaving a 3.5cm gap between them.

For the top, measure 8mm from each short side and mark four evenly spaced intervals. Trace the bowl outlines side by side, leaving a 3.5cm gap between them.For the top, measure 8mm from each short side and mark four evenly spaced intervals. Trace the bowl outlines side by side, leaving a 3.5cm gap between them.

5. Use a drill to make pilot holes at the marks on the top piece.

Use a drill to make pilot holes at the marks on the top piece.Use a drill to make pilot holes at the marks on the top piece.

6. Switch to a larger drill bit and drill four starter holes, about 1cm inside the circle lines. These holes will give your jigsaw a starting point.

Switch to a larger drill bit and drill four starter holes, about 1cm inside the circle lines. These holes will give your jigsaw a starting point.Switch to a larger drill bit and drill four starter holes, about 1cm inside the circle lines. These holes will give your jigsaw a starting point.

7. Use the jigsaw to carefully cut along 1cm from the circle lines, connecting the starter holes you drilled. The circle does not have to be perfect as long as it can fit the bowls.

Use the jigsaw to carefully cut along 1cm from the circle lines, connecting the starter holes you drilled. The circle does not have to be perfect as long as it can fit the bowls.Use the jigsaw to carefully cut along 1cm from the circle lines, connecting the starter holes you drilled. The circle does not have to be perfect as long as it can fit the bowls.

8. Apply wood glue to the top edge of one leg piece and hammer it into place. Repeat with the other side.

Apply wood glue to the top edge of one leg piece and hammer it into place. Repeat with the other side.Apply wood glue to the top edge of one leg piece and hammer it into place. Repeat with the other side.

9. Use a sander to smooth all surfaces and soften the edges, ensuring a neat and safe finish.

Use a sander to smooth all surfaces and soften the edges, ensuring a neat and safe finish.Use a sander to smooth all surfaces and soften the edges, ensuring a neat and safe finish.

Aida Ihsani is a self-taught DIYer and woodworker with over eight years of experience. Through her women’s woodworking workshops, she has empowered over 1,000 women from all walks of life to be confident in using power tools and start their DIY journey. For more on Aida’s workshop, visit www.aidaihsani.com or @iamaidaihsani on Instagram.


Follow us on our official WhatsApp channel for breaking news alerts and key updates!
   

Next In Living

Heart and Soul: Remembering Lavania Baloo, our bravehearted soul sister
Malaysian chef Linn Yong champions sustainable Sabah ingredients
Heart and Soul: Climbing Mt Kilimanjaro, a journey beyond limits
RM1,530 for a coffee? Scottish farm sells Britain's most expensive cup of Joe
Glenfiddich Invites Malaysian Mavericks To Ask Themselves, ‘Where Next?’
Traditional Sabahan recipes get the spotlight at Oitom by chef Raphael Peter Lee
Meet Wanda, the machine that collects and separates trash for recycling
Hide KL takes you on a delicious modern Malaysian odyssey with its latest menu
How these US children with special needs got to 'walk on water'
Cost of convenience: Coffee pods need and waste more resources than other methods

Others Also Read